TunerPro User Forum

Adhamkhe

Maybe Found the issue. The camshaft sensor wasn't connected properly. Will fix it and update

Adhamkhe

Hello It´s a work in progress. I have been comparing with Punto ME2 damos. Which map do you need? Thanks for replying I'm looking for deceleration fuel cut maps and idle ignition maps. I don't think me2 got deceleration ignition map. Right? Let me know if you need addresses for fuel or ignition pt ...

Adhamkhe

Hi so did anyone find a definition file or mappack? I found fuel and ignition timing but nothing else

Adhamkhe

Hi everyone.
Regarding 153 ecu
The revlimiter found on the xdfs is working but I was wondering about the hysterisis regarding it. The 62c4 address for revlimiter primary is followed by 03. And so does the other revlimiter at 62f0. Can that byte 003 be the hysterisis?
Thanks

Adhamkhe

Thanks for the reply. The blue sensor is the one that was replaced ( going to ecu ) problem remains

Adhamkhe

Hi everyone
Car is m20b28( modified engine)
Running 405 ecu and wiring( I know it's for M50)
The car drives perfectly when the chip is first installed then after 30 minutes it goes super rich
Checked the temperature sensor it works normal
Any suggestions???

Adhamkhe

Tried using idle ignition angle 0(rawdata) at the last 2 values? works for getting some pops

Adhamkhe

Solved.
Had to use VPN since It want available for my country

Adhamkhe

Solved.
Had to use VPN since It want available for my country

Adhamkhe

Hi I asked this before but it seems that I used the wrong section of the site.
Bimmer tuning tools website had been showing coming soon on all there products. How can I buy the software does anyone know?
Thanks in advance

Adhamkhe

Hi regarding Bosch 400 to 413 I noticed 2 revlimiters ( 6500 the one usually modified). And another one (6000 rpm. ). What's the other one for?
Please let me know if I understand it correctly in the image below

: IMG-20240104-WA0027.jpg (95.51 KiB) Viewed 1361 times

Any help is greatly appreciated
Thanks in advance

Adhamkhe

After trying for a long time I noticed that lambda adaptation can only change 5%in 402 so disabling it isn't that important

Adhamkhe

Hi found those lambda Maps for 402
7870 6*1
787e 6*1
788a 4*1
7894 4*1
789e 4*1

: IMG-20231224-WA0003.jpg (117.67 KiB) Viewed 1345 times

But lambda off isn't working.
Any suggestions ?

Adhamkhe

Hi everyone.
I'm trying to purchase ms45 quickflash from the original website for a year now but it always says coming soon.
Is there a way I can purchase the original software somewhere else?
Thanks in advance

Adhamkhe

Hi I knew recently that there's a code to insert instead of an ff string to get hardcut revlimit hysterisis 32. And it works on all motronic ecu. Does anyone know if its true and what is it ? If not can anyone tell me where I can get hardcut hysterisis and softcut hysterisis and revlimiter for 402 e...

Adhamkhe

only up Hi is there a way to switch between 2 stacked bins on a double sized chip? (2 files 256 on a 512 chip) Chips typically have memory addresses associated with different locations within the chip. You may need to specify the memory address or range of addresses associated with each bin to acce...

Adhamkhe

Ok thanks for your reply brother

Adhamkhe

Hi I'm searching for a tool that covers all Subaru ecu. Can anyone help with a recommendation for a tool?
Thanks

Adhamkhe

Hi does anyone know the addresses for fuel at declaration and lambda adaptation control tables for 405 ecu.
Thanks in advance

Adhamkhe

Pops and crackle on throttle release while driving is achieved but not when stationary.
If someone knows how I'll be happy to submit mod file

Adhamkhe

Hi my freinds Im trying with this file for 2 days now and cant get pops on throttle release. Its 545i e60 me9.2 Hw: 07544610 Swver: 10373730376 Hw ver: 0261209010 Sw upg: 07561124 Got power and fuel good enough but not getting pops Can anyone tell me the addresses of the table or have an xdf or damo...

Adhamkhe

https://preview.ibb.co/ha2QOw/Sans_titre1.png Set all values to 0 in this table will turn off O2 regulation and adaptatives, did some tests this morning and it works ;) Hi how are you I know that you put a lot of effort in creating that xdf and i noticed that the addresses cover the 2 chips for 403...

Adhamkhe

Adhamkhe wrote: ↑Fri Jul 14, 2023 6:45 am
blacknipel wrote: ↑Fri Apr 17, 2020 5:30 am How can I find this xdf?
Found it?

Its found at 767a or 768a. Refer to picture provided by @evil. Above

Adhamkhe

blacknipel wrote: ↑Fri Apr 17, 2020 5:30 am How can I find this xdf?

Found it?

Adhamkhe

Hi usually theres no problems with the issue of pops but theres a car thats not working well with this. The pops are only happening when slight throttle is applied. The ignition timing low load is set to -13.96( 0 no conversion ) at low load first colomn from 1500 to 6500. And idle ignition timing i...

Adhamkhe

So pin number 1 (vpp programming voltage on 27c256) is (a15. Address 15 on 27c512. ) is that what you recommend using as a switched 5v ?

Adhamkhe

Thanks a lot. I will try that tomorrow

Adhamkhe

Hi is there a way to switch between 2 stacked bins on a double sized chip? (2 files 256 on a 512 chip)

Adhamkhe

Hi everyone
Im trying to access the abs module programming of 2003 e46 in order to change brakes pressure to help with drifting
Did anyone try it before and can help?
Best regards

Adhamkhe

Hi sorry i was busy due to the start of race season Injector constant was put at 18500( raw data) (varies depending on the injectors used. Mine were volvo s40t on m50 turbo) Xdf address was 6a16 (16bit) Hi, What did you put as injector constant value ? Can you show us the parameter of your table XDF...

Adhamkhe

Hi everyone
i have a problem with a 403 ecu mixture getting very rich after engine warms up (using very big injectors but decreased injector constant so the tables are manageable)
Is there a table related to fuel enrichment and engine temperature?
Thanks in advance

Adhamkhe

Tried disabling all lambda adaptation tables using winols. Car turns off after a fraction of a second . Did anyone have this issue?

Adhamkhe

Thanks for your reply olafu
Ill keep trying and will let you know if i have any success with that
Also im searching for the hysteresis but no success yet

Adhamkhe

Hi. Theres a problem that im struggling with and would be very thankful if someone have a solution Running 506_soft965 on 413 red label Revlimit seems to be soft limit (fuel cut ) set 7000 rpm Fuel and ignition tables limit 6500 rpm Ignition dwell limit 7000 rpm The question is. Im not finding a way...

Adhamkhe

The 506 xdf is updated on the tunerpro website. If there's a specific table that you need let me know and ill help as much as i can
Best regards

Adham al khechen
REVUP TUNING
Lebanon

Adhamkhe

This "Vanos dwell table" in XDF from Tunerpro site has nothing to do with vanos. It's injection timing table. M3.3.1 vanos can be full advanced or full retarded, it has no closed loop control like Siemens ecu in M52 engine. Vanos solenoid valve is also different design in M52 to suit clos...

Adhamkhe

Hi
does anyone know what exactly the values at the vanos dwell tables mean? It cant be cam angle since for m52 its between 85 and 110 but the tables go to 255 .
Thanks in advance .

Adhamkhe

Hi freinds. Please note that you cant just use any file on your car even if ""stage1"" every engine is different. A file working great on another car might cause knock on your car . Start with an emulator some knowlage on how the systems work and a knock monitor. (Preferably with...

TunerPro User Forum

Search found 38 matches

Re: Car dumping fuel

Re: Motronic ME2.1 - Mercedes 2.3L Kompressor M111 Questions

Re: Motronic ME2.1 - Mercedes 2.3L Kompressor M111 Questions

153 revlimiter hysterisis address

Re: Car dumping fuel

Car dumping fuel

Re: 413 Burble/Pops and Bangs

Re: Bimmer tuning tools software

Re: Bimmer tuning tools

Bimmer tuning tools

2 revlimiters??

Re: M50 402 disable lambda

Re: M50 402 disable lambda

Bimmer tuning tools software

Coding for creating a hardcut revlimiter

Re: Double size chip map switch

Re: Best tool for tuning Subaru from 1996 to 2023

Best tool for tuning Subaru from 1996 to 2023

motronic 405 or 400 fuel at deceleration and lambda adaptation

Re: Me9.2 pops problem

Me9.2 pops problem

Re:

Re: BMW Bosch motronic 403 Lambda feedback

Re: BMW Bosch motronic 403 Lambda feedback

153 Bosch pops on throttle release

Re: Double size chip map switch

Re: Double size chip map switch

Double size chip map switch

E46 abs module programming

Re: 403 temperature fuel enrichment problem

403 temperature fuel enrichment problem

Re: M50 402 disable lambda

Re: 506 revlimit hysteresis and ignition cut instead of fuel cut

506 revlimit hysteresis and ignition cut instead of fuel cut

Re: NEW BMW 506 xdf

Re: Vanos tuning bosch 413

Vanos tuning bosch 413

Re: Tuned file for stock M50B25TU with red label 413 dme